If you’re looking to Sell Noyes OPM 1-3B SM MM Fiber Power Meter

Noyes OPM 1-3B Optical Power Meter
The OPM 1 optical power meters are inexpensive, simple, portable meters that were first introduced by Noyes Fiber Systems in 1988. With only two controls on the top panel, ON/OFF and wavelength select switch, the OPM 1 Series offers simplicity and total flexibility for all systems. Power measurements in dBm are displayed on the large easy to read LCD. The OPM 1 is guaranteed accurate by Noyes Fiber Systems and is fully N.I.S.T. traceable.

There are four OPM 1 models to choose from to suit your application needs. The OPM 1-1B measures light at 660, 780, and 850 nm; for testing plastic clad silica fibers, LAN, Ethernet, Token Ring, and multimode systems. The OPM 1-2B is calibrated at 850, 1300, and 1550 nm; for testing LAN, Ethernet, FDDI, Token Ring, and singlemode fiber systems such as Telco, WAN, and CATV. The OPM 1-3B also operates at 850, 1300, and 1550 nm; but offers greater temperature stability needed for outside plant 1550 nm testing as with WAN, CATV, and Telco systems. The OPM 1-4B has a measurement range of +23 dBm and is calibrated at 1300, and 1550 nm; for higher power level requirements of CATV, amplifiers, and cellular systems.

Buying, Selling, Trading Noyes OPM 1-3B

The OPM 1 is powered by a standard 9 volt alkaline battery. To conserve battery life, the automatic shut off occurs after 5 minutes. A low battery condition is displayed on the LCD. The universal adapter interface allows connection to a wide variety of fiber optic connector styles.

Features:

• Low Cost, Easy to Use
• Field Porable, Battery Operated
• N.I.S.T. Traceable

If you’re selling your Noyes OPM 1-3B please fill out form on the right hand side of page.

If you’re looking to Sell Noyes OPM 4-4C SM MM Fiber Optic Power Meter

OPM 4-4C Optical Power Meter

The OPM 4 optical power meter may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 4 also measures insertion loss of multimode or single-mode cables. The OPM 4 offers Wave ID, automatic wavelength identification and switching, when used with the OLS 1 Dual or OLS 2 Dual or OLS 4 with Wave ID feature. Multiple test Tone detection is provided for fiber identification. The OPM 4 stores optical references for each calibrated wavelength. An easy to read Dual Wavelength LCD display with Backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge status. In addition to being powered by two AA alkaline, the OPM 4 can be powered by optional AC adapter and/or rechargeable NiMH battery pack. The OPM 4 optical input port accepts Noyes thread-on style adapter caps. Adapter caps are required for operation and must be ordered separately. The OPM 4 is fully N.I.S.T. traceable.

Features:

– Rugged, handheld, lightweight
– Multimode or single-mode applications
– Premises (Ge), Telco (InGaAs), and Broadband (+26 dBm) models
– Wave ID – automatic wavelength identification and switching
– Passive Optical Networks (PON) testing
– Dual Wavelength testing
– 270 Hz, 330 Hz, 1 kHz, and 2 kHz Tone detection
– Large LCD with Backlight
– Power measurements in dBm or µW; insertion loss in dB
– Reference power level storage
– AA alkaline, optional rechargeable NiMH battery pack
– Battery Gauge
– N.I.S.T traceable

Buying, Selling, Trading Noyes OPM 4-4C

If you’re selling your Noyes OPM 4-4C please fill out form on the right hand side of page.

If you’re looking to Sell Noyes OLS 2 SM Fiber Laser Light Source

Noyes OLS 2 Fiber Light Source
The OLS 2 laser source series offers excellent stability and portability for accurate fiber optic testing. Four versions of the OLS 2 are offered for measurements at 1310 nm, 1550 nm, 1625 nm, and dual wavelength (1310/1550 nm). These compact units operate in either continuous wave (CW) mode or 2 kHz modulated mode.

With an output power of -10 dBm, the OLS 2 will provide in excess of 50 dB range when used with Noyes Fiber Systems optical power meters.

The OLS 2 operates on disposable batteries or AC adapter. A Low battery indication warns the user that battery replacement is necessary. The optical output is via a top panel FC, SC, or ST connector. The output may be equipped with other style connectors upon request.

When used with an optical power meter, the OLS 2 laser source provides an inexpensive alternative to higher priced loss test sets. The OLS 2 may be substituted for terminal equipment in the central office or head-end to provide a stable output for loss measurements.

For singlemode applications, such as Telecom or CATV, the OLS 2 may be coupled with an optical power meter as a test kit to perform optical loss tests at 1310 or 1550nm.

In the modulation mode, the OLS 2 applies a 2 kHz tone into the fiber. This signal is detected by the OFI-200B, optical fiber identifier, to isolate specific fibers in a bundle prior to splicing or rerouting.

Applications
When used with an optical power meter, the OLS 2 laser source provides an inexpensive alternative to higher priced loss test sets. The OLS 2 may be substituted for terminal equipment in the central office or head-end to provide a stable output for loss measurements.

For singlemode applications, such as Telecom or CATV, the OLS 2 may be coupled with an optical power meter as a test kit to perform optical loss tests at 1310 or 1550 nm.

In the modulation mode, the OLS 2 applies a 2 kHz tone into the fiber. This signal is detected by the OFI-200B, optical fiberidentifier, to isolate specific fibers in a bundle prior to splicing or rerouting.

Buying, Selling, Trading Noyes OLS 2

If you’re selling your Noyes OLS 2 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes OFI-FTTx Active ONT Fiber Identifier

Noyes OFI-FTTx Active ONT Detector
The OFI-FTTx is a rugged, hand-held optical fiber identifier designed to identify the presence or absence of an active Optical Network Terminal (ONT) on FTTx F2 fibers at the Fiber Distribution Hub (FDH). During a test the F2 fiber does not have to be removed from service. Thus the OFI-FTTx can verify whether a splitter pigtail at the FDH is connected to an active circuit before it is disconnected for fault location or re-use. The OFI-FTTx can help verify FTTx network records and recover splitter pigtails and F2 fibers that are connected at the FDH but, in fact, are available for new customers.

When applied to a splitter pigtail at the FDH, the OFI FTTx will report either that the ONT is ‘Active’ or ‘Not Detected’. Time to complete each test is typically one second. The OFI-FTTx is compatible with 2mm jumper cable containing standard single-mode fiber, such as SMF-28e®, or bend insensitive fiber (BIF) with a 15mm bend radius specification, such as AFL Bend Insensitive.

The OFI-FTTx is powered by two standard AA alkaline batteries, provides a low battery indication, and can typically be operated 800 times before battery replacement is necessary.

Features:

• Rugged, hand-held, lightweight
• In-service detection of upstream (1310 nm) activity on FTTx networks
• Determines which unparked splitter pigtails are connected to ONTs
• Does not require travel to customer (ONT) site
• Does not require disconnect of splitter pigtails
• Visual and audible indicators
• Battery operated
• Low battery indication

Buying, Selling, Trading Noyes OFI-FTTx

Applications:

• FACILITY RECOVERY:
  • Harvest unparked splitter legs and F2 fibers not connected to subscribers.
• TROUBLE-SHOOTING:
  • Real-time confirmation of OLT to ONT connectivity at the FDH.

If you’re selling your Noyes OFI-FTTx please fill out form on the right hand side of page.

If you’re looking to Sell Noyes SLP 6-3 SM Fiber Optic Loss Test Kit

Noyes SLP 6-3 SM Fiber Loss Test Set
The OLS 6 Optical Light Source and OPM 6 Optical Power Meter by Noyes Fiber Systems provide many unique features for testing optical loss in multimode or singlemode fiber cable. Not your typical source and meter, the pair are designed to simultaneously test at 850/1300 or at 1310/1550 nm to quickly provide N.I.S.T. traceable test results.

Other testing features include the ability for the OLS 6 to generate a tone at 270 Hz, 1 kHz, and 2 kHz for fiber identification. This feature is often useful to identify specifi c fibers from a bundle. The OPM 6 performs diagnostic and evaluation measurements associated with fiber optic transmission systems in dB, dBm, and µW.

The easy-to-read display and on-screen commands of the OPM 6 provide simple operation for testing, storing, and editing loss data. The unit’s non – volatile memory can store dual-wavelength test results for up to 960 fibers in up to 10 user-defined files. Using the supplied WindowsTM compatible software, stored files may be transferred to a PC for storage, display, printing, and analysis.

In addition to being powered by two AA alkaline or rechargeable batteries, the OLS 6 and OPM 6 can be powered by optional AC adapters. To conserve battery life, the automatic shut off occurs after 20 minutes if no keys are pressed.

Features:

• Simultaneous loss measurements at 850/1300 nm or 1310/1550 nm
• Singlemode or multimode dual-wavelength testing
• Field storage of 960 loss readings into 10 user-defined groups
• Field portable, battery operated
• Full fiber documentation via WindowsTM 95/98/NT 4.0 data analysis software
• Power measurements at 850,1300, 1310, 1550, and 1625 nm
• N.I.S.T. Traceable

Buying, Selling, Trading Noyes SLP 6-3

If you’re selling your Noyes SLP 6-3 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes FTS1 MM Fiber Optic Talk Set Unit 850nm

Noyes FTS 1-1 Fiber Optic Talk Set
Noyes fiber optic talk sets are an inexpensive solution to meet your multimode or singlemode fiber optic communication needs. Designed for voice communication over spare fibers, they provide full duplex, hands free operation. Ease of use and compact size allow the operators to focus on the task at hand, rather than operating the talk set.

Three talk set models are available. The FTS 1 for communication on singlemode or multimode fiber, and the FTS 2 or FTS 3 for singlemode applications. The FTS 2 and FTS 3 models include a multiparty communication feature which provides the connection of two talk sets at a common site to extend the range or to include three or more persons in the conversation. In addition to voice communications, FTS 3 models also serve as a stabilized light source for loss testing and a 2 kHz tone generator for fiber identification when used with an optical fiber identifier (OFI 200B)..

Buying, Selling, Trading Noyes FTS1

Features:

• Single fiber, full duplex
• Multimode and singlemode models
• Field portable, hands free operation
• Automatic connection
• Multiparty communication

If you’re selling your Noyes FTS1 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes SMLP5-5SM MM Fiber Optic Loss Test Set

Noyes SMLP5-5 Fiber Optic Test Kit

Features

• Handheld, rugged, lightweight
• Wave ID (auto identification & switching)
• Dual or single Wave ID, CW, Tone
• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
• Large LCD with backlight (OPM5-2D)
• Power measurements in dBm or µW, insertion loss in dB
• Reference power level storage
• Up to 500 records per wavelength storage
• USB port for download of stored records
• Windows® compatible software to view, print, and archive stored records
• Low battery indicator
• Long battery life with 2 x AA alkaline, optional AC adapter
• Free 50 µm and 62.5 µm mandrels
• Cost-effective, easy to use
• N.I.S.T traceable

Buying, Selling, Trading Noyes SMLP5-5

The SMLP5-5 test kit combines the OPM5-2D optical power meter and OLS4 integrated LED and LASER light source and is ideally suited for testing fiber optic networks with hybrid (single-mode and multimode) cables.

The OLS4 features 850/1300 nm LED output from a multimode output port and 1310/1550 nm LASER output from a single-mode output port. Each wavelength may be transmitted individually at CW or with user selectable modulated Tone (SM output). Also, each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the OLS4 supports transmitting pairs of wavelengths in an alternating pattern. Associated with each operating condition, the designated LED indicator will illuminate to identify the currently enabled operating mode and emitted wavelength(s) along with battery charge status and external power presence. Both output ports are equipped with UCI based removable adapters to allow the output connectors to be inspected and cleaned.

The OPM5-2D features automatic wavelength identification and switching (Wave ID) when used with the OLS4, multiple test Tone detection for fiber identification, and stores optical references for each calibrated wavelength and up to 500 records per wavelength of power or insertion loss measurements. Using the supplied Windows® compatible software and USB connection, test records are transferred to a PC for analysis, printing, and storage. A large dual-wavelength LCD display with backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining battery life. The OPM5-2D optical input port accepts a variety of Noyes thread-on style adapter caps (ordered separately) to meet a wide range of testing requirements.

The OPM5-2D or OLS4 offer long battery life from common AA alkaline batteries with external AC adapter available as an option.

The SMLP5-5 test kit is fully N.I.S.T. traceable.

If you’re selling your Noyes SMLP5-5 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes T420 Remote SM Fiber Tester

Noyes TurboTest 400 Fiber Loss Test Set
The Turbotest 400 Series Fiber Optic Certification Test Sets are designed to quickly test either multimode or singlemode fiber links, and to generate certification reports based on the latest fiber standards. Two models are available – the T410 operates at 850 and 1300 nm for multimode applications, and the T420 that operates at 1310 and 1550 nm for singlemode applications. Testing fiber cable with the Turbotest 400 Series saves time and money. Once the testing standard has been selected, it’s only moments after pressing the AutoTest key before PASS/FAIL results are displayed. AutoTests are based on length, propagation delay, dual-wavelength loss results and user-supplied data such as the number of splices and connections.The Turbotest 400 can also operate like a traditional optical power meter to measure optical power at 850, 1300, 1310, and 1550 nm. Using the Windows® software, test results can be downloaded to your PC to document your network or to produce professional certification reports for your customer. The Turbotest 400 Series stores up to 1000 fiber test results in user defined files. To speed the testing process, both models can automatically increment fiber numbers. AutoTest certification standards include TIA 568-A, ISO 11801, EN 50173, 10 Base-FL, 100 Base-FX, 1000 Base-SX, 1000 Base-LX, and FDDI. Additional certification standards can be programmed by the user.

Features:

• Measure loss and length on Singlemode fiber links
• Modular transmit and receive ports
• Selectable certification standards providing PASS/FAIL results
• Store test results for up to 1,000 fibers in user-defined files

Buying, Selling, Trading Noyes T420

If you’re selling your Noyes T420 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes T410 Remote MM Fiber Tester

Noyes TurboTest 400 Fiber Loss Test Set
The Turbotest 400 Series Fiber Optic Certification Test Sets are designed to quickly test either multimode or singlemode fiber links, and to generate certification reports based on the latest fiber standards. Two models are available – the T410 operates at 850 and 1300 nm for multimode applications, and the T420 that operates at 1310 and 1550 nm for singlemode applications. Testing fiber cable with the Turbotest 400 Series saves time and money. Once the testing standard has been selected, it’s only moments after pressing the AutoTest key before PASS/FAIL results are displayed. AutoTests are based on length, propagation delay, dual-wavelength loss results and user-supplied data such as the number of splices and connections.The Turbotest 400 can also operate like a traditional optical power meter to measure optical power at 850, 1300, 1310, and 1550 nm. Using the supplied Windows® software, test results can be downloaded to your PC to document your network or to produce professional certification reports for your customer. The Turbotest 400 Series stores up to 1000 fiber test results in user defined files. To speed the testing process, both models can automatically increment fiber numbers. AutoTest certification standards include TIA 568-A, ISO 11801, EN 50173, 10 Base-FL, 100 Base-FX, 1000 Base-SX, 1000 Base-LX, and FDDI. Additional certification standards can be programmed by the user.

Features:

• Measure loss and length on multimode fiber links
• Modular transmit and receive ports
• Selectable certification standards providing PASS/FAIL results
• Store test results for up to 1,000 fibers in user-defined files

Buying, Selling, Trading Noyes T410

If you’re selling your Noyes T410 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes T-410 Turbotest 400 MM Certification Loss Test Set

Noyes TurboTest 400 Fiber Loss Test Set
The Turbotest 400 Series Fiber Optic Certification Test Sets are designed to quickly test either multimode or singlemode fiber links, and to generate certification reports based on the latest fiber standards. Two models are available – the T410 operates at 850 and 1300 nm for multimode applications, and the T420 that operates at 1310 and 1550 nm for singlemode applications. Testing fiber cable with the Turbotest 400 Series saves time and money. Once the testing standard has been selected, it’s only moments after pressing the AutoTest key before PASS/FAIL results are displayed. AutoTests are based on length, propagation delay, dual-wavelength loss results and user-supplied data such as the number of splices and connections.The Turbotest 400 can also operate like a traditional optical power meter to measure optical power at 850, 1300, 1310, and 1550 nm. Using the supplied Windows® software, test results can be downloaded to your PC to document your network or to produce professional certification reports for your customer. The Turbotest 400 Series stores up to 1000 fiber test results in user defined files. To speed the testing process, both models can automatically increment fiber numbers. AutoTest certification standards include TIA 568-A, ISO 11801, EN 50173, 10 Base-FL, 100 Base-FX, 1000 Base-SX, 1000 Base-LX, and FDDI. Additional certification standards can be programmed by the user.

Features:

• Measure loss and length on multimode fiber links
• Modular transmit and receive ports
• Selectable certification standards providing PASS/FAIL results
• Store test results for up to 1,000 fibers in user-defined files

Buying, Selling, Trading Noyes T-410

If you’re selling your Noyes T-410 please fill out form on the right hand side of page.