If you’re looking to Sell Noyes OPM4 SM MM Fiber Optic Loss Test Set
OLS1 Dual Light Source

OPTICAL

OLS1-DUAL (SINGLE PORT)

Wavelength

850 ±30 nm

1300 +50/-10 nm

Emitter Type

LED,Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03

Spectral Width

40 nm (typ)

120 nm (typ)

Output Power

>-20 dBm b

Output Stability

±0.1 dB over 8 hours (after 5-minute warm-up)

Fiber Size

62.5 µm c

GENERAL

Power

2 AA batteries, optional AC adapter

Battery Life

Typical 30 hours, minimum 20 hours

Available Adapters

SC, FC, ST

Operating Temperature

-10°C to 50°C, 90 % RH (non-condensing)

Storage Temperature

-30°C to 60°C, 90 % RH (non-condensing)

Size (H x W x D)

14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)

Weight

0.29 kg (0.65 lb)
OLS2 Dual Laser Source

The OLS2-Dual from AFL Telecommunications is a handheld, rugged laser source designed for performing insertion loss measurements on single-mode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, the OLS2-Dual may be used for fiber identification. The LASER output is stabilized to ensure accurate test results per current TIA/EIA requirements.

The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port and offers several modes of operation. Each wavelength may be transmitted individually at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs of wavelengths in an alternating pattern. Associated with each operating condition, the designated LED indicator will illuminate to identify the currently enabled operating mode and emitted wavelength(s) along with battery charge status and external power presence.

The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the output connector to be inspected and cleaned. The OLS2-Dual offers long battery life from common AA alkaline batteries with external AC adapter available as an option.
The OLS2-Dual is fully N.I.S.T. traceable.

Features:
• Handheld, rugged, lightweight
• Dual wavelengths from a single port
• Dual or single Wave ID, CW, To
• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
• Adjustable output
• Low battery LED indicator
• Long battery life with 2 x AA alkaline, optional AC adapter
• Cost-effective, easy to use
• N.I.S.T. Traceable
Applications:
• Certify SM links per TIA/EIA standards
• Fiber identification prior to splicing
Noyes OPM 4 – Adds Wave ID & Set Reference

The Noyes OPM 4 optical power meter may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 4 also measures insertion loss of multimode or single-mode cables.

The OPM 4 offers Wave ID, automatic wavelength identification and switching, when used with the OLS 1 Dual or OLS 2 Dual or OLS 4 with Wave ID feature. Multiple test Tone detection is provided for fiber identification. The OPM 4 stores optical references for each calibrated wavelength. An easy to read Dual Wavelength LCD display with Backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge status. In addition to being powered by two AA alkaline, the OPM 4 can be powered by optional AC adapter and/or rechargeable NiMH battery pack.

The OPM 4 optical input port accepts Noyes thread-on style adapter caps. Adapter caps are required for operation and must be ordered separately. The OPM 4 is fully N.I.S.T. traceable.

The OPM 4-4C is calibrated at 850, 980, 1310, 1480, 1550, 1625 nm and designed for the higher power level requirements of long range, amplified optical spans used in CATV and DWDM networks.

Buying, Selling, Trading Noyes OPM4

Specifications:

Optical Specifications OPM 4-4C
Calibrated Wavelengths (nm) 850, 980, 1310, 1480, 1550, 1625
Detector Type Filtered InGaAs
Measurement Range (dBm) +26 to -50
Accuracy (dB) +-.25
Measurement Units dB, dBm, uW
General Specifications
Power typical 60 hours with 9V battery
Adapter caps order separately (ST, SC, FC, and others available)
Operating temperature -10 to 50°C
Relative humidity 0 to 95% (non-condensing)
Storage temperature -30 to 60°C
Size (H x W x D) 5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight 0.58 lb (0.26 kg)

If you’re selling your Noyes OPM4 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes OLS1 MM Fiber Optic Dual Light Source OLS-1

OLS1 LED Light Source
The OLS1 from AFL Telecommunication is a handheld, rugged LED light source designed for performing insertion loss measurements on multimode fiber optic links when used with an optical power meter. The LED output is stabilized to ensure accurate test results per current TIA/EIA requirements.

Buying, Selling, Trading Noyes OLS1

Applications:

• Certify 50 or 62.5 µm multimode fiber links for any 850 or 1300 nm application

If you’re selling your Noyes OLS1 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes OPM4-2 SM MM Fiber Optic Power Meter

OPM 4 Optical Power Meter
The OPM 4 optical power meter may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 4 also measures insertion loss of multimode or single-mode cables. The OPM 4 offers Wave ID, automatic wavelength identification and switching, when used with the OLS 1 Dual or OLS 2 Dual or OLS 4 with Wave ID feature. Multiple test Tone detection is provided for fiber identification. The OPM 4 stores optical references for each calibrated wavelength. An easy to read Dual Wavelength LCD display with Backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge status. In addition to being powered by two AA alkaline, the OPM 4 can be powered by optional AC adapter and/or rechargeable NiMH battery pack. The OPM 4 optical input port accepts Noyes thread-on style adapter caps. Adapter caps are required for operation and must be ordered separately. The OPM 4 is fully N.I.S.T. traceable.

Features:

• Rugged, handheld, lightweight
• Multimode or single-mode applications
• Premises (Ge), Telco (InGaAs), and Broadband (+26 dBm) models
• Wave ID – automatic wavelength identification and switching
• Passive Optical Networks (PON) testing
• Dual Wavelength testing
• 270 Hz, 330 Hz, 1 kHz, and 2 kHz Tone detection
• Large LCD with Backlight
• Power measurements in dBm or µW; insertion loss in dB
• Reference power level storage
• AA alkaline, optional rechargeable NiMH battery pack
• Battery Gauge
• N.I.S.T traceable

Buying, Selling, Trading Noyes OPM4-2

If you’re selling your Noyes OPM4-2 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes MLP 1-1 MM Light Pack MM Fiber Test Kit

Noyes OPM 1-1

This portable optical power meter may be used to measure optical power in premises, telco, or broadband fiber optic networks. When used with an LED or laser light source, the OPM 1 can also measure the attenuation (insertion loss) of multimode or single-mode cables. With only two controls – ON/OFF and wavelength – the OPM 1 is our simplest to use optical power meter. Optical power in dBm and the calibration wavelength setting are displayed on an easy-to-read LCD display. The optical input port accepts Noyes thread-on style connector adapter caps. Adapter caps are required and must be ordered separately. The OPM 1 is fully N.I.S.T. traceable and runs on a standard 9-volt alkaline battery.

MLP 1-1

The MLP 1 test kits are inexpensive solutions for testing multimode and single-mode systems. By joining the OPM 1 optical power meter and the OLS 1 optical light source, the MLP 1 is a great kit for beginners or network owners. Two versions of the MLP1 test kit are available for testing Premises networks, LAN, and Gigabit Ethernet.

Buying, Selling, Trading Noyes MLP 1-1

Features:

Multimode Testing
Loss measurements at 850
Field portable, battery operated
N.I.S.T. traceable
OLS 1-1

Output ports 1
Output wavelength 850 + 35/-40 nm
Spectral width (typ) (FWHM) 40 nm
Output power -20 dBm
Stability (@25°C, 5 min. warm-up) 0.1 dB over 8 hours
Fiber size 62.5 µm
Emitter type Class 1 (IEC 60825 – 1)
Power Typical 60 hours with 9V battery, optional AC adapter
Connector ST
Size (H x W x D) 5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight 0.65 lb (.29 kg)

If you’re selling your Noyes MLP 1-1 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes FTS3 Fiber Optic Talk Set

FTS 3 Fiber-optic Talk Set

The FTS 3 works directly with terminated optical connectors and can also be used as a stabilized laser source to perform loss tests. The FTS 3 can also generate and receive a 2kHz Tone for fiber identification.

Buying, Selling, Trading Noyes FTS3

The FTS 3 Fiber-optic Talk Set is intended primarily for use on spare (dark) fibers to allow users to communicate while testing other fibers in the bundle.  The FTS 3 is useful where other types of communication are not available or desirable; for example, new construction where standart telephone lines have not yet been installed or a tunnel where radios may not work well.

If you’re selling your Noyes FTS3 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes OPM 4-4D SM MM Fiber Optic Power Meter

OPM 4 Optical Power Meter

The OPM 4 optical power meter may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 4 also measures insertion loss of multimode or single-mode cables. The OPM 4 offers Wave ID, automatic wavelength identification and switching, when used with the OLS 1 Dual or OLS 2 Dual or OLS 4 with Wave ID feature. Multiple test Tone detection is provided for fiber identification. The OPM 4 stores optical references for each calibrated wavelength. An easy to read Dual Wavelength LCD display with Backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge status. In addition to being powered by two AA alkaline, the OPM 4 can be powered by optional AC adapter and/or rechargeable NiMH battery pack. The OPM 4 optical input port accepts Noyes thread-on style adapter caps. Adapter caps are required for operation and must be ordered separately. The OPM 4 is fully N.I.S.T. traceable.

Buying, Selling, Trading Noyes OPM 4-4D

Features:

• Rugged, handheld, lightweight
• Multimode or single-mode applications
• Premises (Ge), Telco (InGaAs), and Broadband (+26 dBm) models
• Wave ID – automatic wavelength identification and switching
• Passive Optical Networks (PON) testing
• Dual Wavelength testing
• 270 Hz, 330 Hz, 1 kHz, and 2 kHz Tone detection
• Large LCD with Backlight
• Power measurements in dBm or µW; insertion loss in dB
• Reference power level storage
• AA alkaline, optional rechargeable NiMH battery pack
• Battery Gauge
• N.I.S.T traceable

If you’re selling your Noyes OPM 4-4D please fill out form on the right hand side of page.

If you’re looking to Sell Noyes OPM5 SM MM Power Meter OPM5-4C

Noyes OPM5 Power Meter

The OPM 5 is used to perform diagnostic and evaluation measurements associated with fiber optic transmission systems  and cable plant. Applications for the OPM 5 will be found within the telecommunication, cable television, data network, and  industrial control industries.

The OPM 5 measures absolute power (in dBm or µW ) and loss (dB). Absolute power expressed in dBm is the amount of  optical power received by the detector as compared to 1mW (0dBm=1mW). Measuring dBm is useful for verifying the output  power of a transmitter and determining system losses.

Loss is the difference in optical power from a known input (the reference level) and the output power at the opposite end of  the fiber under test. The OPM 5 can display dB loss directly after a reference level has been set. Loss measurements are  used to qualify cable plant links and fiber optic jumpers.

Microwatts is also a way to measure absolute power. Some manufacturers specify their transmission equipment in watts  instead of dBm. The OPM 5 offers the ability to measure watts for convenience when verifying output power of transmitters. For accurate results, always be sure to set the OPM 5 to measure the same wavelength as the output of the optical light  source.

OPM5-4C specifications

Buying, Selling, Trading Noyes OPM5

If you’re selling your Noyes OPM5 please fill out form on the right hand side of page
.

If you’re looking to Sell Noyes OPM4 SM MM Fiber Optic Loss Test Set

OLS 1-2

Optical Light Source OLS 1-2
Wavelength 850, 1300nm
Emitter Type LED
Stability ±0.1 dB/8 hrs.
Output Power
Multimode (62.5/125µm) -20dBm @ 850nm, -20dBm @ 1300nm
Single-mode ( 9/125µm) -40dBm @ 1300nm
Power 80 hrs. typical operation with 9V alkaline,
AC adapter optional
Optical Connectors ST
Size (H x W x D) 4.6 x 2.6 x 1.2in (11.7 x 6.6 x 3.2cm)

OLS2D

The OLS2-Dual from AFL Telecommunications is a handheld, rugged laser source designed for performing insertion loss measurements on single-mode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, the OLS2-Dual may be used for fiber identification. The LASER output is stabilized to ensure accurate test results per current TIA/EIA requirements.

The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port and offers several modes of operation. Each wavelength may be transmitted individually at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs of wavelengths in an alternating pattern. Associated with each operating condition, the designated LED indicator will illuminate to identify the currently enabled operating mode and emitted wavelength(s) along with battery charge status and external power presence.

The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the output connector to be inspected and cleaned. The OLS2-Dual offers long battery life from common AA alkaline batteries with external AC adapter available as an option.
The OLS2-Dual is fully N.I.S.T. traceable.

Buying, Selling, Trading Noyes OPM4

Features:
• Handheld, rugged, lightweight
• Dual wavelengths from a single port
• Dual or single Wave ID, CW, To
• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
• Adjustable output
• Low battery LED indicator
• Long battery life with 2 x AA alkaline, optional AC adapter
• Cost-effective, easy to use
• N.I.S.T. Traceable
Applications:
• Certify SM links per TIA/EIA standards
• Fiber identification prior to splicing
Noyes OPM 4 – Adds Wave ID & Set Reference

The Noyes OPM 4 optical power meter may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 4 also measures insertion loss of multimode or single-mode cables.

The OPM 4 offers Wave ID, automatic wavelength identification and switching, when used with the OLS 1 Dual or OLS 2 Dual or OLS 4 with Wave ID feature. Multiple test Tone detection is provided for fiber identification. The OPM 4 stores optical references for each calibrated wavelength. An easy to read Dual Wavelength LCD display with Backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge status. In addition to being powered by two AA alkaline, the OPM 4 can be powered by optional AC adapter and/or rechargeable NiMH battery pack.

The OPM 4 optical input port accepts Noyes thread-on style adapter caps. Adapter caps are required for operation and must be ordered separately. The OPM 4 is fully N.I.S.T. traceable.

The OPM 4-2C is calibrated at 850, 1300, 1310 and 1550 nm for testing LAN, FDDI, ethernet, token ring and single-mode fiber systems such as telco, WAN, and CATV.
Specifications

Optical Specifications OPM 4-2C
Calibrated Wavelengths (nm) 850, 1300, 1310, 1550
Detector Type Germanium (Ge)
Measurement Range (dBm) +6 To -60
Accuracy (dB) +-.25
Measurement Units dB, dBm, uW
General Specifications
Power typical 60 hours with 9V battery
Adapter caps order separately (ST, SC, FC, and others available)
Operating temperature -10 to 50°C
Relative humidity 0 to 95% (non-condensing)
Storage temperature -30 to 60°C
Size (H x W x D) 5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight 0.58 lb (0.26 kg)

If you’re selling your Noyes OPM4 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes OPM 4-4D & OFS 300 Fiber Inspection Kit

OPM 4-4D Optical Power Meter

The OPM 4 optical power meter may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 4 also measures insertion loss of multimode or single-mode cables. The OPM 4 offers Wave ID, automatic wavelength identification and switching, when used with the OLS 1 Dual or OLS 2 Dual or OLS 4 with Wave ID feature. Multiple test Tone detection is provided for fiber identification. The OPM 4 stores optical references for each calibrated wavelength. An easy to read Dual Wavelength LCD display with Backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge status. In addition to being powered by two AA alkaline, the OPM 4 can be powered by optional AC adapter and/or rechargeable NiMH battery pack. The OPM 4 optical input port accepts Noyes thread-on style adapter caps. Adapter caps are required for operation and must be ordered separately. The OPM 4 is fully N.I.S.T. traceable.

Features:

– Rugged, handheld, lightweight
– Multimode or single-mode applications
– Premises (Ge), Telco (InGaAs), and Broadband (+26 dBm) models
– Wave ID – automatic wavelength identification and switching
– Passive Optical Networks (PON) testing
– Dual Wavelength testing
– 270 Hz, 330 Hz, 1 kHz, and 2 kHz Tone detection
– Large LCD with Backlight
– Power measurements in dBm or µW; insertion loss in dB
– Reference power level storage
– AA alkaline, optional rechargeable NiMH battery pack
– Battery Gauge
– N.I.S.T traceable

Buying, Selling, Trading Noyes OPM 4-4D & OFS 300

The OFS 300 is a versatile instrument for the inspection of optical fiber connectors. By employing a universal adapter mount, the OFS 300 offers the ability to inspect virtually any connector style for scratches, dirt, or other problems normally associated with poor transmission performance.OFS 300-200c

The OFS 300-200C offers precision 200x magnification to easily inspect both multimode and single-mode fiber optic connectors.

The OFS 300 offers 60 hours of continuous battery life. A low battery indicator will flash when approximately 8 hours of optimum brightness remains reducing the risk of eye strain. Various adapter caps are available to convert the mount to the desired connector style. The OFS 300-200C uses the same common threaded connector adapter caps as the Noyes Optical Power Meters and Loss Test Sets.

If you’re selling your Noyes OPM 4-4D & OFS 300 please fill out form on the right hand side of page.

If you’re looking to Sell Noyes MLP 1-2 MM Light Pack MM Fiber Test Kit

Noyes OPM 1-2

This portable optical power meter may be used to measure optical power in premises, telco, or broadband fiber optic networks. When used with an LED or laser light source, the OPM 1 can also measure the attenuation (insertion loss) of multimode or single-mode cables. With only two controls – ON/OFF and wavelength – the OPM 1 is our simplest to use optical power meter. Optical power in dBm and the calibration wavelength setting are displayed on an easy-to-read LCD display. The optical input port accepts Noyes thread-on style connector adapter caps. Adapter caps are required and must be ordered separately. The OPM 1 is fully N.I.S.T. traceable and runs on a standard 9-volt alkaline battery.

MLP 1-2

The MLP 1 test kits are inexpensive solutions for testing multimode and single-mode systems. By joining the OPM 1 optical power meter and the OLS 1 optical light source, the MLP 1 is a great kit for beginners or network owners. Two versions of the MLP1 test kit are available for testing Premises networks, LAN, and Gigabit Ethernet.

Buying, Selling, Trading Noyes MLP 1-2

Features:

• Multimode Testing
• Loss measurements at 850 and 1300nm
• Includes 50 and 62.5 µm mandrels
• Field portable, battery operated
• Certify 50 or 62.5 µm multimode fiber links for any 850 or 1300nm application, including Gigabit Ethernet (GBE)
• N.I.S.T. traceable

If you’re selling your Noyes MLP 1-2 please fill out form on the right hand side of page.